-
Sep 22, 2015, 04:48 PM
#11
Big Member
Originally Posted by
Seriously
OMG, that's had one hard life !
I prefer the term well appreciated
What about using a flap disc? Those are some pretty good scratches and dings
-
Post Thanks / Like - 1 Likes
-
Sep 22, 2015, 06:54 PM
#12
Moderator
Originally Posted by
Henry Krinkle
I am having better luck with the crystal than the case.
What do you use for the crystal? I have a couple with hardened glass crystals and quite a few scratches and can get anywhere near cleaning them up.
-
Post Thanks / Like - 1 Likes
-
Sep 24, 2015, 02:22 PM
#13
Originally Posted by
Henry Krinkle
The chrome cases are nearly impossible to sand. I am having better luck with the crystal than the case.
Dremel and file work?
-
Post Thanks / Like - 1 Likes
-
Sep 24, 2015, 03:15 PM
#14
Originally Posted by
Chase
I prefer the term well appreciated
What about using a flap disc? Those are some pretty good scratches and dings
I always sand by hand on a flat surface. I fix sandpaper to something called die matrix, which is a highly stable and super flat form of ply wood. It's a little like the plywood used to make race boats. When I am doing angles I build a jig so that I minimize wobble. I hate rounded edges where they should be sharp.
-
Sep 24, 2015, 03:16 PM
#15
Originally Posted by
93EXCivic
Dremel and file work?
Sorry, I'd have multi-quoted you but I missed yours. I never use power tools. Much of my enjoyment comes from the meditative nature of drawing the case back and forth, back and forth...
-
Sep 24, 2015, 03:19 PM
#16
Originally Posted by
scottjc
What do you use for the crystal? I have a couple with hardened glass crystals and quite a few scratches and can get anywhere near cleaning them up.
I use waterproof automotive refinishing grits. I will often put something like swirl remover on the sandpaper first.
I no longer know what the dial on this is. It is much harder than acrylic but I am having luck with the haze and shallow scratches. It takes a lot of work though.
-
Sep 24, 2015, 04:40 PM
#17
Moderator
Originally Posted by
Henry Krinkle
I use waterproof automotive refinishing grits. I will often put something like swirl remover on the sandpaper first.
I no longer know what the dial on this is. It is much harder than acrylic but I am having luck with the haze and shallow scratches. It takes a lot of work though.
Thanks mate.
I suspect you may be dealing with hardened glass and am looking forward to seeing your final results.
-
Dec 2, 2015, 04:19 PM
#18
-
Dec 2, 2015, 05:29 PM
#19
Originally Posted by
93EXCivic
Any update on this one?
Not a good one...
It is one of the Louis Rossel chrome hardened steel cases, which usually don't scratch. They dimple. It is almost impossible to sand these ans if the scratches are deep enough one can scratch through to the steel underneath. The steel is slightly yellower than the chrome and shows...and, I'm there. Or near enough.
-
Dec 2, 2015, 06:42 PM
#20
Moderator
Originally Posted by
Henry Krinkle
Not a good one...
It is one of the Louis Rossel chrome hardened steel cases, which usually don't scratch. They dimple. It is almost impossible to sand these ans if the scratches are deep enough one can scratch through to the steel underneath. The steel is slightly yellower than the chrome and shows...and, I'm there. Or near enough.
That's a shame Henry but that's the joy of vintage watches, for each gem there's a couple of turkeys hidden away in the drawer.