-
Jul 14, 2019, 06:51 PM
#1
if not look for a thin metal spacer that takes up the space and holds it firm . but still reckon a front loader
sharky
one of the most original good guys their was never anything but a true friend "the daito to my shoto"
rest easy good buddy
https://gofund.me/eb610af1
-
Post Thanks / Like - 1 Likes
-
Jul 15, 2019, 12:21 AM
#2
Member
Is this a Longines cal.17.69NZ?
-
Jul 15, 2019, 12:36 AM
#3
Originally Posted by
morningtundra
You were right. Once I got the bezel off it dropped out. The dial looks to be pretty fragile. Any suggestions how to clean this? Or even how to get it off in one piece?
Think I’ve found a parts donor for this too...
Sent from my cracked, broken hand wound phone. IG @morning_tundra
well once the hands come off there would be maybe two screws one opposite the other on the side of the movement which you loosen then the dial would lift up and out but with the damage it's tricky some times had one did look two bad till I removed it and it had a crack I could not see and broke in two so yeah good luck with that .. but hard to say with it looking at it from all angles .
as for cleaning dials depend which one if the dial is a transfer print I would use a cotton wool buds and a week washing up mix to remove the dirt ..
but you have to watch out thou as with some printing you can remove it too , so always do a small test area first
sharky
one of the most original good guys their was never anything but a true friend "the daito to my shoto"
rest easy good buddy
https://gofund.me/eb610af1
-
Jul 15, 2019, 02:05 AM
#4
Member
Originally Posted by
is that my watch
well once the hands come off there would be maybe two screws one opposite the other on the side of the movement which you loosen then the dial would lift up and out but with the damage it's tricky some times had one did look two bad till I removed it and it had a crack I could not see and broke in two so yeah good luck with that .. but hard to say with it looking at it from all angles .
as for cleaning dials depend which one if the dial is a transfer print I would use a cotton wool buds and a week washing up mix to remove the dirt ..
but you have to watch out thou as with some printing you can remove it too , so always do a small test area first
It might be an utter disaster and I’ll just have to live with the guilt of destroying it if I goof up.
Don’t think those hands will want to come off easily. Is there anything I can treat them with to loosen them up first? Some kind of penetrating oil?
Sent from my cracked, broken hand wound phone. IG @morning_tundra
-
Jul 15, 2019, 06:14 PM
#5
Originally Posted by
morningtundra
It might be an utter disaster and I’ll just have to live with the guilt of destroying it if I goof up.
Don’t think those hands will want to come off easily. Is there anything I can treat them with to loosen them up first? Some kind of penetrating oil?
Sent from my cracked, broken hand wound phone. IG @morning_tundra
not sure I got lubricating oil but hmmm would a very small amount of wd40 work I wonder or would it affect the other oil's in the watch ? I just normally use my hand removing tool
sharky
one of the most original good guys their was never anything but a true friend "the daito to my shoto"
rest easy good buddy
https://gofund.me/eb610af1
-
Jul 15, 2019, 07:21 PM
#6
Originally Posted by
morningtundra
... Is there anything I can treat them with to loosen them up first? Some kind of penetrating oil?
Try heat first - A soldering iron is the best option - Rest the tip on the centre for a few minutes to heat it up, then stick it in an air-tight bag (or wrap in cling film) and into the freezer. The expansion & contraction might be just enough to 'crack' any crusty bits.
Failing that: A small drop of 'PlusGas'. WD40 is more of a moisture repellent than a penetrating fluid, and it leaves a sticky residue.
Some people have opinions - The rest of us have taste.
-
Jul 15, 2019, 07:30 PM
#7
Originally Posted by
crownpuller
Try heat first - A soldering iron is the best option - Rest the tip on the centre for a few minutes to heat it up, then stick it in an air-tight bag (or wrap in cling film) and into the freezer. The expansion & contraction might be just enough to 'crack' any crusty bits.
Failing that: A small drop of 'PlusGas'. WD40 is more of a moisture repellent than a penetrating fluid, and it leaves a sticky residue.
think the heat then cold would finish the dial off with those hair line cracks but it's a thought
sharky
one of the most original good guys their was never anything but a true friend "the daito to my shoto"
rest easy good buddy
https://gofund.me/eb610af1
-
Jul 15, 2019, 07:40 PM
#8
Originally Posted by
is that my watch
think the heat then cold would finish the dial off with those hair line cracks but it's a thought
The heat shouldn't 'touch' the dial; but good point about the freezing - I don't know how enamel reacts to the cold ? Enamel bakeware is capable of cooking and freezing.... not sure if the same type of enamel.
Some people have opinions - The rest of us have taste.